Data-Driven Modeling for Additive Manufacturing of Metals: Proceedings of a Workshop (2019)
Chapter: Appendix B: Workshop Agenda
B
Workshop Agenda
A Workshop on the Frontiers of Mechanistic Data-Driven Modeling for
Additive Manufacturing
October 24–26, 2018
Neue Materialien Fürth GmbH
Dr.-Mack-Straße 81, Technikum 1, 6th Floor
Fürth, Germany
Day 1: October 24
| 9:00 a.m. | Welcome from the Co-Chairs |
Carolin Körner, Co-Chair, Friedrich-Alexander Universität Erlangen-Nürnberg | |
Wing Kam Liu, Co-Chair, Northwestern University | |
| 9:20 a.m. | Opening Comments from the Sponsors |
R. Allen Roach, Sandia | |
Richard Ricker, NIST | |
| 9:40 a.m. | Opening Comments from the National Academies |
Michelle Schwalbe, Board on Mathematical Sciences and Analytics | |
Erik Svedberg, National Materials and Manufacturing Board |
SESSION 1: MEASUREMENTS AND MODELING FOR PROCESS MONITORING AND CONTROL
| 10:00 a.m. | Introduction to Session 1 |
Bianca Colosimo, Politecnico di Milano | |
| 10:10 a.m. | Measurement Science for Process Monitoring and Control |
Jarred Heigel, National Institute of Standards and Technology | |
| 10:40 a.m. | Break |
| 11:00 a.m. | Process Simulation as a Complement of Process Monitoring1 |
Daniel Reznik, Siemens | |
| 11:30 a.m. | Lunch |
| 12:30 p.m. | Panel Discussion |
| |
| Panelists: | |
Bianca Colosimo, Politecnico di Milano | |
Ben Dutton, Manufacturing Technology Centre | |
Jarred Heigel, National Institute of Standards and Technology | |
Daniel Reznik, Siemens | |
Kilian Wasmer, Empa | |
Amit Surana, United Technologies Research Center | |
| 2:00 p.m. | Break |
SESSION 2: DEVELOPING MODELS TO REPRESENT MICROSTRUCTURE EVOLUTION, ALLOY DESIGN, AND PART SUITABILITY
| 2:30 p.m. | Introduction to Session 2 |
| Lyle Levine, National Institute of Standards and Technology | |
___________________
1 Unable to attend.
| 2:35 p.m. | Measurements for Additive Manufacturing of Metals |
Lyle Levine, National Institute of Standards and Technology | |
| 3:05 p.m. | Break |
| 3:30 p.m. | Predicting Material State and Performance of Additively Manufactured Parts |
Kyle Johnson, Sandia National Laboratories | |
| 4:00 p.m. | Panel Discussion |
| |
| Panelists: | |
Lyle Levine, National Institute of Standards and Technology | |
Eric Jägle, Max Planck Institute | |
Kyle Johnson, Sandia National Laboratories | |
Christian Leinenbach, Empa | |
Deniece Korzekwa, Los Alamos National Laboratory | |
Annett Seide, MTU Aero Engines | |
John Turner, Oak Ridge National Laboratory | |
| 5:30 p.m. | Conclude Sessions |
Day 2: October 25
| 9:00 a.m. | Recap of Day 1; Major Themes and Overview for the Day |
Session 1: Bianca Colosimo | |
Session 2: Lyle Levine |
SESSION 3: MODELING ASPECTS OF PROCESS AND MACHINE DESIGN
| 9:30 a.m. | Introduction to Session 3 |
Tahany El-Wardany, United Technologies Research Center | |
| 9:40 a.m. | Current State of Commercial Powder-Bed Additive Machines—Improvements Needed to Minimize Build-to-Build Variability |
| Ade Makinde, General Electric Global Research Center, with support from Johannes Henrich Schleifenbaum, Fraunhofer Institute for Laser Technology, and Shoufeng Yang, KU Leuven | |
| 10:10 a.m. | Break |
| 10:30 a.m. | Modeling Challenges and Opportunities at the Part Level |
| Jian Cao, Northwestern University, with support from Ranadip Acharya, United Technologies Research Center, and Mustafa Megahed, ESI Group | |
| 11:00 a.m. | Panel Discussion |
| |
| Panelists: | |
Tahany El-Wardany, United Technologies Research Center | |
Ranadip Acharya, United Technologies Research Center | |
Jian Cao, Northwestern University | |
Ade Makinde, General Electric Global Research Center | |
Mustafa Megahed, ESI Group | |
Johannes Henrich Schleifenbaum, Fraunhofer Institute for Laser Technology | |
Michael Schmidt, Friedrich-Alexander Universität Erlangen-Nürnberg | |
Shoufeng Yang, KU Leuven | |
| 12:30 p.m. | Lunch |
SESSION 4: ACCELERATING PRODUCT AND PROCESS QUALIFICATION AND CERTIFICATION
| 1:30 p.m. | Introduction to Session 4 |
Paolo Gennaro, GF Precicast Additive SA | |
| 1:35 p.m. | Process Qualification and Technological Validation, from Casting to Additive |
Paolo Gennaro, GF Precicast Additive SA | |
| 2:05 p.m. | Modeling and Simulation |
Michel Delanaye,2 GeonX | |
| 2:35 p.m. | Break |
___________________
| 3:00 p.m. | Panel Discussion |
| |
| Panelists: | |
Paolo Gennaro, GF Precicast Additive SA | |
Vincent Paquit, Oak Ridge National Laboratory | |
Jens Telgkamp, Airbus Operations GmbH | |
Michel Delanaye, GeonX | |
David Teter, Los Alamos National Laboratory | |
Richard Ricker, National Institute of Standards and Technology | |
| 5:00 p.m. | Conclude Presentations and Discussions |
Day 3: October 26
| 9:00 a.m. | Recap of Day 2; Major Themes and Overview for the Day |
| Session 3: Tahany El-Wardany | |
| Session 4: Paolo Gennaro | |
| 9:30 a.m. | Breakout Groups |
| |
| 12:00 p.m. | Lunch (with Breakout Groups) |
| 1:00 p.m. | Breakout Groups Report Back |
| 2:30 p.m. | Final Comments from Co-Chairs and Sponsors |
Carolin Körner, Co-Chair, Friedrich-Alexander Universität Erlangen-Nürnberg | |
Wing Kam Liu, Co-Chair, Northwestern University | |
Sponsors’ Representatives | |
| 3:00 p.m. | Adjourn Workshop |
